-- *****************************************************************
-- CISCO-ENTITY-DIAG-MIB
-- Definitions of managed objects supporting the Online
-- Diagnostic Feature
--
-- November 2002, Patrick Gili
-- October 2005, Jayakumar Kadirvelu
--
-- Copyright (c) 2002-2008 by Cisco Systems Inc.
-- All rights reserved.
-- ****************************************************************CISCO-ENTITY-DIAG-MIB DEFINITIONS::=BEGINIMPORTSOBJECT-GROUP,MODULE-COMPLIANCE,NOTIFICATION-GROUPFROM SNMPv2-CONF
Unsigned32,Gauge32,Integer32,Counter32,OBJECT-TYPE,MODULE-IDENTITY,NOTIFICATION-TYPEFROM SNMPv2-SMI
entPhysicalIndex,PhysicalIndex,entPhysicalDescr
FROM ENTITY-MIB
SnmpAdminStringFROM SNMP-FRAMEWORK-MIB
DateAndTime,TruthValue,
RowStatusFROM SNMPv2-TC
EntPhysicalIndexOrZero
FROM CISCO-TC
CeDiagDiagnosticLevel,
CeDiagDiagnosticMethod,
CeDiagTestIdentifier,
CeDiagErrorIdentifier,
CeDiagErrorIdentifierOrZero,
CeDiagJobIdentifier,
CeDiagPortList,
CeDiagTestList,
CeDiagJobSuite
FROM CISCO-ENTITY-DIAG-TC-MIB
ciscoMgmt
FROM CISCO-SMI;ciscoEntityDiagMIB MODULE-IDENTITYLAST-UPDATED"200803120000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO"Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
Tel: +1 800 553-NETS
E-mail: cs-snmp@cisco.com"DESCRIPTION"This MIB module defines the managed objects that describe the
online diagnostics capabilities supported by the
physical entities contained by the system, including chassis,
modules, ports, power supplies, fans, and sensors. In order to
manage the online diagnostic capabilities supported by
a physical entity, it must be represented by a conceptual row
in the entPhysicalTable of the ENTITY-MIB (RFC-2737).
GLOSSARY
Boot-up Diagnostic - a diagnostic consisting of tests intended
to be executed in a reasonable timeframe when a physical entity
boots.
Diagnostic - a suite of tests intended to exercise the
functional integrity of a physical entity.
Diagnostic Level - the degree of completeness that a diagnostic
will exercise a physical entity.
Field Diagnostic - a special suite of tests intended to
exercise the functional integrity of a physical entity in a
manner that is possible when a physical entity is
operational or running an operational image.
Field Diagnostic Image - an image supporting field diagnostics.
A physical entity has to be loaded with a field diagnostic
image before field diagnostics can be executed on the physical
entity.
Health Monitoring - the process of running special
non-intrusive online tests periodically on a physical entity
for the purpose of tracking the overall condition of a physical
entity.
On-Demand Diagnostic - a diagnostic intended to be executed
immediately upon request.
Offline Diagnostic - a diagnostic that consists of tests that
are disruptive in nature, and thus requires the physical entity
being evaluated to be taken offline for the duration.
Online Diagnostic - a diagnostic that consists of tests that
are not disruptive in nature, and thus can be done without
taking the physical entity offline.
Physical Entity - an identifiable physical resource, such as a
chassis, line card, power supply, or communication port. See
RFC-2737, 'Entity MIB (Version 2)', K. McCloghrie and A.
Bierman.
Scheduled Diagnostic - a diagnostic intended to execute at some
time in the future. There exist two types of scheduled
diagnostics: 1) one-shot, which execute only once; and 2)
periodic, which executes at a specific interval.
Test - an exercise intended to determine the functional
integrity of a component comprising a physical entity (e.g., a
port might support an internal loopback test).
Diagnostic Job - Consists of a diagnostic suite
(i.e., a collection of tests) to be executed by a physical
entity."REVISION"200803120000Z"DESCRIPTION"Added ceDiagNotifControlGroup, ceDiagNotifErrorMsgGroup
and ceDiagNotificationGroup."REVISION"200701090000Z"DESCRIPTION"Initial version of this MIB."::={ ciscoMgmt 350}
ciscoEntityDiagMIBNotifs OBJECTIDENTIFIER::={ ciscoEntityDiagMIB 0}ciscoEntityDiagMIBObjects OBJECTIDENTIFIER::={ ciscoEntityDiagMIB 1}ciscoEntityDiagMIBConform OBJECTIDENTIFIER::={ ciscoEntityDiagMIB 2}ceDiagDescriptions OBJECTIDENTIFIER::={ ciscoEntityDiagMIBObjects 1}ceDiagGlobalConfig OBJECTIDENTIFIER::={ ciscoEntityDiagMIBObjects 2}ceDiagEntity OBJECTIDENTIFIER::={ ciscoEntityDiagMIBObjects 3}ceDiagOnDemand OBJECTIDENTIFIER
::={ ciscoEntityDiagMIBObjects 4}ceDiagScheduled OBJECTIDENTIFIER::={ ciscoEntityDiagMIBObjects 5}ceDiagTest OBJECTIDENTIFIER::={ ciscoEntityDiagMIBObjects 6}ceDiagHealthMonitor OBJECTIDENTIFIER::={ ciscoEntityDiagMIBObjects 7}ceDiagEvents OBJECTIDENTIFIER::={ ciscoEntityDiagMIBObjects 8}ceDiagNotificationControl OBJECTIDENTIFIER::={ ciscoEntityDiagMIBObjects 9}-- DiagDescriptionsceDiagTestInfoTable OBJECT-TYPESYNTAXSEQUENCEOF CeDiagTestInfoEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table describes the tests supported by each physical
entity supporting online diagnostics. The table
organizes tests into sets associated with the physical entity
supporting those tests.
The SNMP entity adds a set of tests corresponding to a physical
entity upon detection of a physical entity supporting
online diagnostics.
The SNMP entity deletes a set of tests corresponding to a
physical entity upon removal of the physical entity.
The SNMP entity replaces a set of tests corresponding to a
physical entity when the physical entity has been successfully
loaded with a different image (e.g., the field diagnostic
image)."::={ ceDiagDescriptions 1}ceDiagTestInfoEntry OBJECT-TYPESYNTAX CeDiagTestInfoEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The description of a single test supported by a corresponding
physical entity."INDEX{
entPhysicalIndex,
ceDiagTestId
}::={ ceDiagTestInfoTable 1}
CeDiagTestInfoEntry ::=SEQUENCE{
ceDiagTestId CeDiagTestIdentifier,
ceDiagTestText SnmpAdminString,
ceDiagTestAttributes BITS}ceDiagTestId OBJECT-TYPESYNTAX CeDiagTestIdentifier
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object indicates an arbitrary positive integer
arbitrarily identifying the test."::={ ceDiagTestInfoEntry 1}ceDiagTestText OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-only
STATUScurrentDESCRIPTION"This object indicates a human-readable description of the
test. Examples include:
'Marching Pattern DRAM Test'
'Data Pins DRAM Test'
'Internal Loopback Test'
'External Loopback Test'"::={ ceDiagTestInfoEntry 2}ceDiagTestAttributes OBJECT-TYPESYNTAXBITS{minimal(0),complete(1),perPort(2),fatal(3),basicOnDemand(4),standby(5),parallel(6),
nonDisruptive(7),hmAlwaysEnable(8),hmFixedInterval(9),nonHM(10),proxy(11),activeToStandby(12),offline(13),perDevice(14)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates a set of attributes characterizing the
test:
'minimal' - indicates that this test will be executed
during boot-up if ceDiagBootupLevel is set
to 'minimal' or 'complete'. This test is
also included in the minimal or complete
test suites.
'complete' - indicates that this test will be executed
during boot-up if ceDiagBootupLevel is set
to 'complete'. This test is also included
in the complete test suites.
'perPort' - indicates that this test is a executed for
each port contained by the module. This
test is also included in the perPort test
suites.
'fatal' - indicates that if this test fails, then the
diagnostic should fail indicating that a
major error occurred.
'basicOnDemand' - indicates that this test will be
run during the basic on demand job is run.
'standby' - indicates that this test can only be run
if the physical entity is a standby unit
and can only be executed from the standby
unit.
'parallel' - indicates that this test can be executed in
parallel with other tests without checking
for resource availability.
'nonDisruptive' - indicates this test can be executed without
disrupting the physical entity's normal
operation. This test is also included in
the nonDisruptive test suites.
'hmAlwaysEnabled' - indicates that a management application can
not disable the use of this test for the
purpose of health monitoring.
'hmFixedInterval' - indicates that a management application can
not change the interval at which health
monitoring executes this test.
'nonHM' - indicates that this test can not be used for
health monitoring.
'proxy' - indicates that the test must be executed
through a proxy.
'activeToStandby' - indicates that this test can only be run if
the physical entity is a standby unit and
can only be executed from the active unit.
'offline' - indicates that this test will not get a user
confirmation when it is run.
'perDevice' - indicates that this test is a per device test."::={ ceDiagTestInfoEntry 3}ceDiagTestCustomAttributeTable OBJECT-TYPESYNTAXSEQUENCEOF CeDiagTestCustomAttributeEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table describes the additional custom based attributes
of the tests listed in ceDiagTestInfoTable. These are attributes
which have been customized by the platform supporting the tests."::={ ceDiagDescriptions 2}ceDiagTestCustomAttributeEntry OBJECT-TYPESYNTAX CeDiagTestCustomAttributeEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The description of a single custom based attribute for a test
supported by a corresponding physical entity."INDEX{
entPhysicalIndex,
ceDiagTestId,
ceDiagTestCustomAttributeIndex
}::={ ceDiagTestCustomAttributeTable 1}
CeDiagTestCustomAttributeEntry ::=SEQUENCE{
ceDiagTestCustomAttributeIndex Unsigned32,
ceDiagTestCustomAttributeDesc SnmpAdminString}ceDiagTestCustomAttributeIndex OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An arbitrary integer which identifies the custom based attribute
of a test."::={ ceDiagTestCustomAttributeEntry 1}ceDiagTestCustomAttributeDesc OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object provides a textual description of the custom based
attribute of this test."::={ ceDiagTestCustomAttributeEntry 2}
ceDiagErrorInfoTable OBJECT-TYPESYNTAXSEQUENCEOF CeDiagErrorInfoEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table describes the errors indicated by a system
supporting online diagnostics."::={ ceDiagDescriptions 3}ceDiagErrorInfoEntry OBJECT-TYPESYNTAX CeDiagErrorInfoEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The description of a single online error."INDEX{ ceDiagErrorId }::={ ceDiagErrorInfoTable 1}
CeDiagErrorInfoEntry ::=SEQUENCE{
ceDiagErrorId CeDiagErrorIdentifier,
ceDiagErrorText SnmpAdminString
}ceDiagErrorId OBJECT-TYPESYNTAX CeDiagErrorIdentifier
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object indicates an arbitrary positive integer
arbitrarily identifying the error."::={ ceDiagErrorInfoEntry 1}ceDiagErrorText OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates a human-readable description of the
error. Examples include:
'DIAG_SUCCESS'
'DIAG_FAILURE'
'DIAG_NOT_SUPPORT'
'DIAG_SKIPPED'"::={ ceDiagErrorInfoEntry 2}-- DiagGlobalConfigceDiagBootupLevel OBJECT-TYPESYNTAX CeDiagDiagnosticLevel
MAX-ACCESSread-write
STATUScurrentDESCRIPTION"This object specifies the level that physical entities will
execute their boot-up diagnostic."DEFVAL{ minimal }::={ ceDiagGlobalConfig 1}-- DiagEntityceDiagEntityTable OBJECT-TYPESYNTAXSEQUENCEOF CeDiagEntityEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table supports online diagnostic control and
status for each physical entity that supporting the feature.
The SNMP entity adds a conceptual row to this table
corresponding to a physical entity upon detection of a physical
entity supporting online diagnostics.
The SNMP entity deletes a conceptual row from this table
corresponding to a physical entity upon removal of the physical
entity."::={ ceDiagEntity 1}
ceDiagEntityEntry OBJECT-TYPESYNTAX CeDiagEntityEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Online diagnostic control and status for a single
physical entity supporting the feature. Observe that this data
may not be accurate if the corresponding cefcModuleOperStatus
(see the CISCO-ENTITY-FRU-CONTROL-MIB for further details) has
a value of 'boot'."INDEX{ entPhysicalIndex }::={ ceDiagEntityTable 1}
CeDiagEntityEntry ::=SEQUENCE{
ceDiagEntityBootLevel CeDiagDiagnosticLevel,
ceDiagEntityImageAdminStatus INTEGER,
ceDiagEntityImageOperStatus INTEGER,
ceDiagEntityFieldDiagnosticUrl SnmpAdminString}ceDiagEntityBootLevel OBJECT-TYPESYNTAX CeDiagDiagnosticLevel
MAX-ACCESSread-only
STATUScurrentDESCRIPTION"This object indicates the level that the physical entity
executed its boot-up diagnostic."::={ ceDiagEntityEntry 1}ceDiagEntityImageAdminStatus OBJECT-TYPESYNTAXINTEGER{operational(1),fieldDiagnostic(2)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the desired image the physical entity
should be running:
'operational' - the physical entity should be running the
operational image.
'fieldDiagnostic' - the physical entity should be running the
field diagnostic image."DEFVAL{ operational }::={ ceDiagEntityEntry 2}ceDiagEntityImageOperStatus OBJECT-TYPESYNTAXINTEGER{operational(1),fieldDiagnostic(2),booting(3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the actual image the physical entity is
running:
'operational' - the physical entity is running the
operational image.
'fieldDiagnostic' - the physical entity is running the field
diagnostic image.
'booting' - the physical entity is booting; that is,
there is no way of determining what image
the physical entity is running because it
is currently booting."::={ ceDiagEntityEntry 3}ceDiagEntityFieldDiagnosticUrl OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies a URL (see RFC-1630) that specifies the
location of the field diagnostic image. The following list
provides some examples of URLs for the field diagnostic:
file://disk0:/images/fd001
Describes a file with the path '/images/fd001' on 'disk0:'
accessed locally.
ftp://pop-server/usr/bin/fd001
Describes a file with the path '/usr/bin/fd001' on the host
'pop-server' accessed via FTP.
tftp://pop-server/tftpout/fd001
Describes a file with the path '/tftpout/fd001' on the host
'pop-server' accessed via TFTP."REFERENCE"RFC-1630, 'Universal Resource Identifiers in WWW', T.
Berners-Lee."::={ ceDiagEntityEntry 4}ceDiagEntityCurrentTestTable OBJECT-TYPE
SYNTAXSEQUENCEOF CeDiagEntityCurrentTestEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains the information about the current test
executing on a physical entity."::={ ceDiagEntity 2}ceDiagEntityCurrentTestEntry OBJECT-TYPESYNTAX CeDiagEntityCurrentTestEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A test which is currently executing on a particular physical
entity."INDEX{
entPhysicalIndex,
ceDiagTestId
}::={ ceDiagEntityCurrentTestTable 1}
CeDiagEntityCurrentTestEntry ::=SEQUENCE{
ceDiagEntityCurrentTestMethod CeDiagDiagnosticMethod
}ceDiagEntityCurrentTestMethod OBJECT-TYPESYNTAX CeDiagDiagnosticMethod
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the method used to invoke the diagnostic
that is executing this test."::={ ceDiagEntityCurrentTestEntry 1}-- DiagOnDemandceDiagOnDemandErrorAllowed OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the number of errors the physical
entities will allow before aborting an on demand diagnostic job.
A value of '0' indicates that the an unlimited number of
errors are allowed for the on demand diagnostic job."::={ ceDiagOnDemand 1}ceDiagOnDemandErrorAction OBJECT-TYPE
SYNTAXINTEGER{continue(1),stop(2)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies how the physical entities in the
system are to proceed when they encounter an error during
an on demand diagnostic job.
'continue' - indicates that the physical entities will continue
executing the on demand job.
'stop' - indicates that the physical entities will abort
the on demand job."::={ ceDiagOnDemand 2}ceDiagOnDemandIterations OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the maximum number of iterations of an
on demand job."::={ ceDiagOnDemand 3}ceDiagOnDemandJobTable OBJECT-TYPESYNTAXSEQUENCEOF CeDiagOnDemandJobEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains a list of on demand jobs currently in the
system.
A row in this table can be created by setting the corresponding
instance of ceDiagOnDemandJobRowStatus to 'createAndGo'.
A row can be deleted by setting the corresponding instance of
ceDiagOnDemandJobRowStatus to 'destroy'. Once the job is
completed the corresponding row is deleted from the table.
The individual results of the tests executed by this job are
updated in ceDiagTestPerfTable."::={ ceDiagOnDemand 4}ceDiagOnDemandJobEntry OBJECT-TYPESYNTAX CeDiagOnDemandJobEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"A on demand job currently executing on a particular physical
entity which supports on demand diagnostics."INDEX{ entPhysicalIndex }::={ ceDiagOnDemandJobTable 1}
CeDiagOnDemandJobEntry ::=SEQUENCE{
ceDiagOnDemandJobSuite CeDiagJobSuite,
ceDiagOnDemandJobTestList CeDiagTestList,
ceDiagOnDemandJobPortList CeDiagPortList,
ceDiagOnDemandJobRowStatus RowStatus}ceDiagOnDemandJobSuite OBJECT-TYPESYNTAX CeDiagJobSuite
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object indicates the various system predefined test
suites the on demand job can choose from.
If the value of this object is 'none', this job will run
the tests specified by ceDiagOnDemandJobTestList.
If the value of this object is 'complete', 'minimal',
'nonDisruptive' or 'perPort' the value of
ceDiagOnDemandJobTestList is ignored."::={ ceDiagOnDemandJobEntry 1}ceDiagOnDemandJobTestList OBJECT-TYPESYNTAX CeDiagTestList
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the user specified diagnostic suite
(i.e., a set of tests) to be executed by the corresponding
physical entity.
The set of tests supported by this physical entity are
specified in ceDiagTestInfoTable."::={ ceDiagOnDemandJobEntry 2}ceDiagOnDemandJobPortList OBJECT-TYPESYNTAX CeDiagPortList
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the list of ports to be exercised by the
corresponding physical entity when executing the diagnostic
suite specified for the job."::={ ceDiagOnDemandJobEntry 3}ceDiagOnDemandJobRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The status object used to manage the rows in this table.
When set to active(1) the on demand job is submitted.
When set to destroy(6) the on demand job is stopped.
When the value of this object is 'active', values within
this row cannot be modified, except by deleting and
re-creating the row."::={ ceDiagOnDemandJobEntry 4}-- DiagScheduledceDiagScheduledJobTable OBJECT-TYPESYNTAXSEQUENCEOF CeDiagScheduledJobEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains a list of scheduled jobs on the system.
A row in this table can be created by setting the corresponding
instance of ceDiagScheduledJobRowStatus to 'createAndGo'.
A row can be deleted by setting the corresponding instance of
ceDiagScheduledJobRowStatus to 'destroy'. Once the job is
completed the corresponding row is deleted from the table.
The individual results of the tests executed by this job are
updated in ceDiagTestPerfTable."::={ ceDiagScheduled 1}ceDiagScheduledJobEntry OBJECT-TYPESYNTAX CeDiagScheduledJobEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A job currently scheduled on a particular physical
entity."INDEX{
entPhysicalIndex,
ceDiagScheduledJobIndex
}::={ ceDiagScheduledJobTable 1}
CeDiagScheduledJobEntry ::=SEQUENCE{
ceDiagScheduledJobIndex CeDiagJobIdentifier,
ceDiagScheduledJobType INTEGER,
ceDiagScheduledJobStart DateAndTime,
ceDiagScheduledJobDayOfWeek INTEGER,
ceDiagScheduledJobTestList CeDiagTestList,
ceDiagScheduledJobPortList CeDiagPortList,
ceDiagScheduledJobRowStatus RowStatus,
ceDiagScheduledJobSuite CeDiagJobSuite
}ceDiagScheduledJobIndex OBJECT-TYPESYNTAX CeDiagJobIdentifier
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An arbitrary non-zero integer value that uniquely identifies a
single scheduled job with respect to a physical entity."::={ ceDiagScheduledJobEntry 1}ceDiagScheduledJobType OBJECT-TYPESYNTAXINTEGER{scheduledOneShot(1),
scheduledPeriodicDaily(2),scheduledPeriodicWeekly(3)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the type of the scheduled job.
'scheduledOneShot' - the physical entity will invoke
this job at the time specified
by ceDiagScheduledJobStart.
'scheduledPeriodicDaily' - the physical entity will
first invoke this job at the time
specified by
ceDiagScheduledJobStart and
continue invoking it daily at the
same time.
'scheduledPeriodicWeekly' - the corresponding physical entity
will first invoke this job at the
time and day of the week specified
by ceDiagScheduledJobStart and
ceDiagScheduledJobDayOfWeek, and
continue to invoke it weekly at
the same time and day."::={ ceDiagScheduledJobEntry 2}ceDiagScheduledJobStart OBJECT-TYPESYNTAXDateAndTimeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies when a scheduled job will be executed.
If the value of ceDiagScheduledJobType is 'scheduledOneShot',
then this object only applies to the first execution of the job.
If the value of ceDiagScheduledJobType is
'scheduledPeriodicDaily' or 'scheduledPeriodicWeekly', then the
first four octets of this objects should be zero.
If the physical entity's job queue already contains a job
scheduled for execution at this time, then the process of
submitting the job will fail."::={ ceDiagScheduledJobEntry 3}ceDiagScheduledJobDayOfWeek OBJECT-TYPESYNTAXINTEGER{sunday(1),
monday(2),tuesday(3),wednesday(4),thursday(5),friday(6),saturday(7),notApplicable(8)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the day of the week for a
weekly periodic scheduled job. The value of
of this object must be specified if the value of
ceDiagScheduledJobType is 'scheduledPeriodicWeekly'.
This value of this object is set to 'notApplicable'
if the value of ceDiagScheduledJobType is 'scheduledOneShot'
or 'scheduledPeriodicDaily'."::={ ceDiagScheduledJobEntry 4}ceDiagScheduledJobTestList OBJECT-TYPESYNTAX CeDiagTestList
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the diagnostic suite (i.e., a set of
tests) to be executed by the corresponding physical entity.
The set of tests supported by this physical entity are
specified in ceDiagTestInfoTable."::={ ceDiagScheduledJobEntry 5}ceDiagScheduledJobPortList OBJECT-TYPESYNTAX CeDiagPortList
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the list of ports to be tested by the
corresponding physical entity when executing the diagnostic
suite specified for the job."::={ ceDiagScheduledJobEntry 6}
ceDiagScheduledJobRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The status object used to manage the rows in this table.
When set to 'active' the scheduled job is submitted.
When set to destroy(6) the scheduled job is cleared.
When the value of this object is 'active', values within
this row cannot be modified, except by deleting and
re-creating the row."::={ ceDiagScheduledJobEntry 7}ceDiagScheduledJobSuite OBJECT-TYPESYNTAX CeDiagJobSuite
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object indicates the various system predefined test
suites the on scheduled job can choose from.
If the value of this object is 'none', this job will run
the tests specified by ceDiagScheduledJobTestList.
If the value of this object is 'complete', 'minimal',
'nonDisruptive' or 'perPort' the value of
ceDiagScheduledJobTestList is ignored."::={ ceDiagScheduledJobEntry 8}-- DiagTestceDiagTestPerfTable OBJECT-TYPESYNTAXSEQUENCEOF CeDiagTestPerfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table maintains data concerning the performance of tests
executed by each physical entity supporting the online
diagnostic feature. The table organizes tests into sets
associated with the physical entity supporting those tests.
The SNMP entity adds a set of tests corresponding to a physical
entity upon detection of a physical entity supporting
online diagnostics.
The SNMP entity deletes a set of tests corresponding to a
physical entity upon removal of the physical entity.
The SNMP entity replaces a set of tests corresponding to a
physical entity when the physical entity has been successfully
loaded with a different image (e.g., the field diagnostic
image)."::={ ceDiagTest 1}
ceDiagTestPerfEntry OBJECT-TYPESYNTAX CeDiagTestPerfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Data concerning the performance of a single test."INDEX{
entPhysicalIndex,
ceDiagTestId
}::={ ceDiagTestPerfTable 1}
CeDiagTestPerfEntry ::=SEQUENCE{
ceDiagTestPerfLastResult INTEGER,
ceDiagTestPerfLastErrorID CeDiagErrorIdentifierOrZero,
ceDiagTestPerfLastRun DateAndTime,
ceDiagTestPerfFirstFail DateAndTime,
ceDiagTestPerfLastSuccess DateAndTime,
ceDiagTestPeffLastFail DateAndTime,
ceDiagTestPerfTotalRuns Counter32,
ceDiagTestPerfTotalFails Counter32,
ceDiagTestPerfConsecutiveFails Gauge32}ceDiagTestPerfLastResult OBJECT-TYPESYNTAXINTEGER{unknown(1),fail(2),pass(3),skipped(4)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the result the last time this test was
executed by the corresponding physical entity:
'unknown' - the corresponding physical entity has not executed
the test.
'fail' - the test executed and detected at least one
failure.
'pass' - the test executed without detecting a failure.
'skipped' - the test was skipped due to insufficient resources."::={ ceDiagTestPerfEntry 1}ceDiagTestPerfLastErrorID OBJECT-TYPESYNTAX CeDiagErrorIdentifierOrZero
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If the corresponding physical entity has not executed this
test since the last restart, then the value of this object will
be '0'.
If the value of ceDiagTestPerfLastResult is 'fail', then this
object specifies the error associated with the failure.
This object will be have the value of '0' under the following
circumstances:
1) the value of ceDiagTestPerfLastResult is 'pass' or
'unknown'."::={ ceDiagTestPerfEntry 2}ceDiagTestPerfLastRun OBJECT-TYPESYNTAXDateAndTimeMAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object indicates the last time the
corresponding physical entity executed this test. If the value
of ceDiagTestPerfLastResult is 'unknown', then the value of
this object is irrelevant."::={ ceDiagTestPerfEntry 3}ceDiagTestPerfFirstFail OBJECT-TYPESYNTAXDateAndTimeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the first time
the corresponding physical entity executed this test and it
failed. The value of this object is irrelevant if the value of
ceDiagTestPerfTotalFails is 0."::={ ceDiagTestPerfEntry 4}ceDiagTestPerfLastSuccess OBJECT-TYPESYNTAXDateAndTimeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the last time the
corresponding physical entity executed this test and
it passed. The value 0x0000010100000000 indicates
that the corresponding physical entity has not
passed this test yet."::={ ceDiagTestPerfEntry 5}ceDiagTestPeffLastFail OBJECT-TYPESYNTAXDateAndTimeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the last time the
corresponding physical entity executed this test and it failed.
If the value of ceDiagTestPerfTotalFails is 0, then the value
of this object is irrelevant."::={ ceDiagTestPerfEntry 6}ceDiagTestPerfTotalRuns OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the total number of times the
corresponding physical entity has executed the test."::={ ceDiagTestPerfEntry 7}ceDiagTestPerfTotalFails OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the total number of times the
corresponding physical entity has executed the test and the
test resulted with a failure."::={ ceDiagTestPerfEntry 8}ceDiagTestPerfConsecutiveFails OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the consecutive number of times the
corresponding physical entity has executed the test and it has
failed. The value of this object will be reset to '0' when the
physical entity executes the test and it succeeds."::={ ceDiagTestPerfEntry 9}
-- DiagHealthMonitorceDiagHMSyslogEnabled OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies whether the system will generate
syslog messages due to the tests run by health
monitor."::={ ceDiagHealthMonitor 1}ceDiagHMTestTable OBJECT-TYPESYNTAXSEQUENCEOF CeDiagHMTestEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table describes attributes specific to the health monitor
for tests supported by a physical entity."::={ ceDiagHealthMonitor 2}ceDiagHMTestEntry OBJECT-TYPE
SYNTAX CeDiagHMTestEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The attributes of a single test specific to the health
monitor."INDEX{
entPhysicalIndex,
ceDiagTestId
}::={ ceDiagHMTestTable 1}
CeDiagHMTestEntry ::=SEQUENCE{
ceDiagHMTestEnabled TruthValue,
ceDiagHMTestIntervalMin Unsigned32,
ceDiagHMTestIntervalDefault Unsigned32,
ceDiagHMTestInterval Unsigned32,
ceDiagHMTestThresholdDefault Unsigned32,
ceDiagHMTestThreshold Unsigned32}ceDiagHMTestEnabled OBJECT-TYPESYNTAXTruthValue
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies whether this test is enabled for
health monitor."::={ ceDiagHMTestEntry 1}ceDiagHMTestIntervalMin OBJECT-TYPESYNTAXUnsigned32(0..2147483647)UNITS"milliseconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the minimum interval which the health
monitor can periodically invoke this test."::={ ceDiagHMTestEntry 2}ceDiagHMTestIntervalDefault OBJECT-TYPESYNTAXUnsigned32(0..2147483647)
UNITS"milliseconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the default interval which the health
monitor will periodically invoke this test. A value of '0'
indicates that the health monitor will not invoke the test."::={ ceDiagHMTestEntry 3}ceDiagHMTestInterval OBJECT-TYPESYNTAXUnsigned32(0..2147483647)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the interval at which the health monitor
periodically invokes this test. A value of '0' indicates that
the health monitor will not invoke the test. A value of '0'
cannot be set."::={ ceDiagHMTestEntry 4}
ceDiagHMTestThresholdDefault OBJECT-TYPESYNTAXUnsigned32(0..2147483647)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the default consecutive failure
count threshold. When the specified failure count threshold
is reached, the diagnostic test result is set to failure.
A value of '0' indicates that the health monitor will not
invoke this test."::={ ceDiagHMTestEntry 5}ceDiagHMTestThreshold OBJECT-TYPESYNTAXUnsigned32(0..2147483647)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the consecutive failure count threshold
for this test. When the specified failure count threshold is
reached, the diagnostic test result is set to failure.
A value of '0' indicates that there is no consecutive
failure count threshold for this test."::={ ceDiagHMTestEntry 6}-- DiagEventsceDiagEventLogSize OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the maximum number of entries which the
event log buffer can contain."::={ ceDiagEvents 1}ceDiagEventCount OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of entries currently stored
in the event log buffer."::={ ceDiagEvents 2}ceDiagEventMaxQueries OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Maximum number of query entries allowed in the
ceDiagEventQueryTable."::={ ceDiagEvents 3}ceDiagEventQueryTable OBJECT-TYPESYNTAXSEQUENCEOF CeDiagEventQueryEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A control table used to query the event log buffer. Each row
instance in the table represents a query with its parameters.
The resulting data for each instance of a query in this table
is stored in the ceDiagEventResultTable.
A row in this table can be created by setting the corresponding
instance of ceDiagEventQueryStatus to 'createAndGo'.
A row can be deleted by setting the corresponding instance of
ceDiagEventQueryStatus to 'destroy'."::={ ceDiagEvents 4}ceDiagEventQueryEntry OBJECT-TYPESYNTAX CeDiagEventQueryEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row of the ceDiagEventQueryTable used to setup
a event log buffer query to search for diagnostic events.
The actual search is started by when the value of
ceDiagEventQueryStatus is set to 'active'."INDEX{ ceDiagEventQueryIndex }::={ ceDiagEventQueryTable 1}
CeDiagEventQueryEntry ::=SEQUENCE{
ceDiagEventQueryIndex Unsigned32,
ceDiagEventQueryPhysicalIndex EntPhysicalIndexOrZero,
ceDiagEventQuerySeverity INTEGER,
ceDiagEventQueryOwner SnmpAdminString,
ceDiagEventQueryResultingRows Integer32,
ceDiagEventQueryStatus RowStatus}ceDiagEventQueryIndex OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An arbitrary integer in the range of 1 to
ceDiagEventMaxQueries to identify this control query."::={ ceDiagEventQueryEntry 1}ceDiagEventQueryPhysicalIndex OBJECT-TYPESYNTAX EntPhysicalIndexOrZero
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the physical entity for the event
log buffer query. A value of zero indicates that the
query will return events of all physical entities."::={ ceDiagEventQueryEntry 2}
ceDiagEventQuerySeverity OBJECT-TYPESYNTAXINTEGER{all(0),info(1),warning(2),error(3)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the severity of the event log buffer
query. A value of 'all' indicates that the search will return
events of all severities."::={ ceDiagEventQueryEntry 3}ceDiagEventQueryOwner OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-createSTATUScurrent
DESCRIPTION"The manager entity that configured this entry and is therefore
using the resources assigned to it. It is used to model an
administratively assigned name of the owner of a resource.
It is recommended that this object have one or more the following
information: IP address, management station name, network
manager's name, location, or phone number."::={ ceDiagEventQueryEntry 4}ceDiagEventQueryResultingRows OBJECT-TYPESYNTAXInteger32(-1..2147483647)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The result status of the query. Possible values are:
-1 - Either the query has not been initiated or
the agent is busy processing this query instance.
Time to completion of the query processing
depends on the complexity of the query and
the number of matches that satisfy this query.
0..2147483647 - The search has ended and this is the number of
rows in the ceDiagEventResultTable, resulting
from this query."::={ ceDiagEventQueryEntry 5}ceDiagEventQueryStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The status object used to manage rows in this table.
When set to 'active', the query to search for diagnostic
events is initiated. Once a row becomes active, values
within the row cannot be modified, except by deleting
and re-creating the row."::={ ceDiagEventQueryEntry 6}ceDiagEventResultTable OBJECT-TYPESYNTAXSEQUENCEOF CeDiagEventResultEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table containing event log information corresponding
to all the completed queries set up in ceDiagEventQueryTable.
The query result will not become available until the current
search is completed."::={ ceDiagEvents 5}ceDiagEventResultEntry OBJECT-TYPESYNTAX CeDiagEventResultEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row in ceDiagEventResultTable, containing
information about an event that matches the search criteria
set in the corresponding row of ceDiagEventQueryTable."INDEX{
ceDiagEventQueryIndex,
ceDiagEventResultIndex
}::={ ceDiagEventResultTable 1}
CeDiagEventResultEntry ::=SEQUENCE{
ceDiagEventResultIndex Unsigned32,
ceDiagEventResultPhysicalIndex PhysicalIndex,
ceDiagEventResultPhysicalDescr SnmpAdminString,
ceDiagEventResultTime DateAndTime,
ceDiagEventResultSeverity INTEGER,
ceDiagEventResultLogText SnmpAdminString}ceDiagEventResultIndex OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A positive integer which uniquely identifies a result
entry matching a particular query."::={ ceDiagEventResultEntry 1}ceDiagEventResultPhysicalIndex OBJECT-TYPESYNTAXPhysicalIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the physical entity corresponding
to this event."::={ ceDiagEventResultEntry 2}ceDiagEventResultPhysicalDescr OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies a textual description of physical
entity corresponding to this event."::={ ceDiagEventResultEntry 3}ceDiagEventResultTime OBJECT-TYPESYNTAXDateAndTimeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the time at which this event occurred."::={ ceDiagEventResultEntry 4}ceDiagEventResultSeverity OBJECT-TYPESYNTAXINTEGER{
info(1),warning(2),error(3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the severity of this event."::={ ceDiagEventResultEntry 5}ceDiagEventResultLogText OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The text message of this event."::={ ceDiagEventResultEntry 6}ceDiagEventErrorMsg OBJECT-TYPESYNTAXSnmpAdminString
MAX-ACCESSaccessible-for-notifySTATUScurrentDESCRIPTION"The error message related to the notification."::={ ceDiagEvents 6}-- Notification ControlceDiagEnableBootUpFailedNotif OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This variable specifies whether the system produces the
ceDiagBootUpFailedNotif. A 'false' value will prevent
ceDiagBootUpFailedNotif notifications from being
generated by this system."::={ ceDiagNotificationControl 1}ceDiagEnableHMThreshReachedNotif OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION
"This variable specifies whether the system produces the
ceDiagHMThresholdReachedNotif. A 'false' value will prevent
ceDiagHMThresholdReachedNotif notifications from being
generated by this system."::={ ceDiagNotificationControl 2}ceDiagEnableHMTestRecoverNotif OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This variable specifies whether the system produces the
ceDiagHMTestRecoverNotif. A 'false' value will prevent
ceDiagHMTestRecoverNotif notifications from being
generated by this system."::={ ceDiagNotificationControl 3}ceDiagEnableSchedTestFailedNotif OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This variable specifies whether the system produces the
ceDiagScheduledTestFailedNotif. A 'false' value will prevent
ceDiagScheduledTestFailedNotif notifications from being
generated by this system."::={ ceDiagNotificationControl 4}-- NotificationsceDiagBootUpFailedNotif NOTIFICATION-TYPEOBJECTS{
entPhysicalDescr,
ceDiagEntityBootLevel,
ceDiagEventErrorMsg
}STATUScurrentDESCRIPTION"A ceDiagBootUpFailedNotif is sent if the online diagnostic
discovers a boot up failure for a physical entity."::={ ciscoEntityDiagMIBNotifs 1}ceDiagHMThresholdReachedNotif NOTIFICATION-TYPEOBJECTS{
entPhysicalDescr,
ceDiagHMTestThreshold,
ceDiagTestText,
ceDiagTestAttributes
}STATUScurrentDESCRIPTION"A ceDiagHMThresholdReachedNotif is sent if the number of
consecutive failure of a Health Monitoring test reaches
the configured threshold."::={ ciscoEntityDiagMIBNotifs 2}ceDiagHMTestRecoverNotif NOTIFICATION-TYPEOBJECTS{
entPhysicalDescr,
ceDiagTestText,
ceDiagTestAttributes
}STATUScurrentDESCRIPTION"A ceDiagHMTestRecoverNotif is sent when no error is
detected for the first time on the same Health Monitoring test
which previously triggered ceDiagHMThresholdReachedNotif."::={ ciscoEntityDiagMIBNotifs 3}ceDiagScheduledTestFailedNotif NOTIFICATION-TYPEOBJECTS{
entPhysicalDescr,
ceDiagTestText,
ceDiagEventErrorMsg
}STATUScurrentDESCRIPTION"A ceDiagScheduledTestFailedNotif is sent if a scheduled
test failed."::={ ciscoEntityDiagMIBNotifs 4}-- ConformanceciscoEntityDiagMIBCompliances OBJECTIDENTIFIER::={ ciscoEntityDiagMIBConform 1}ciscoEntityDiagMIBGroups OBJECTIDENTIFIER::={ ciscoEntityDiagMIBConform 2}ciscoEntityDiagMIBComplianceRev1 MODULE-COMPLIANCESTATUSdeprecatedDESCRIPTION"The compliance statement for SNMP entities that implement the
CISCO-ENTITY-DIAG-MIB. Implementation of this MIB module is
strongly recommended for any platform implementing the
online diagnostic feature."MODULE-- this moduleMANDATORY-GROUPS{
ceDiagDescrGroup,
ceDiagGlobalConfigGroup,
ceDiagEntityGroup,
ceDiagOnDemandGroup,
ceDiagScheduledGroup,
ceDiagTestPerfGroup,
ceDiagEventGroup
}GROUP ceDiagEntityImageGroup
DESCRIPTION"The objects defined by this group only need to be
implemented if the physical entities in the system
are capable of running their own diagnostic image."GROUP ceDiagHealthMonitorGroup
DESCRIPTION"The objects defined by this group only need to be
implemented if the online diagnostic feature
supports a health monitor."GROUP ceDiagScheduledJobSuiteGroup
DESCRIPTION"The objects defined by this group only need to be
implemented if the online diagnostic feature
supports scheduled job test suites."::={ ciscoEntityDiagMIBCompliances 1}ciscoEntityDiagMIBComplianceRev2 MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for SNMP entities that implement the
CISCO-ENTITY-DIAG-MIB. Implementation of this MIB module is
strongly recommended for any platform implementing the
online diagnostic feature."MODULE-- this moduleMANDATORY-GROUPS{
ceDiagDescrGroup,
ceDiagGlobalConfigGroup,
ceDiagEntityGroup,
ceDiagOnDemandGroup,
ceDiagScheduledGroup,
ceDiagTestPerfGroup,
ceDiagEventGroup
}GROUP ceDiagEntityImageGroup
DESCRIPTION"The objects defined by this group only need to be
implemented if the physical entities in the system
are capable of running their own diagnostic image."GROUP ceDiagHealthMonitorGroup
DESCRIPTION"The objects defined by this group only need to be
implemented if the online diagnostic feature
supports a health monitor."GROUP ceDiagScheduledJobSuiteGroup
DESCRIPTION"The objects defined by this group only need to be
implemented if the online diagnostic feature
supports scheduled job test suites."GROUP ceDiagNotifControlGroup
DESCRIPTION"This group is mandatory for devices which can provide
online diagnostic notifications."GROUP ceDiagNotifErrorMsgGroup
DESCRIPTION"This group is mandatory for devices which can provide
online diagnostic notifications."GROUP ceDiagNotificationGroup
DESCRIPTION"This group is mandatory for devices which can provide
online diagnostic notifications."::={ ciscoEntityDiagMIBCompliances 2}
-- Units of ConformanceceDiagDescrGroup OBJECT-GROUPOBJECTS{
ceDiagTestText,
ceDiagTestAttributes,
ceDiagTestCustomAttributeDesc,
ceDiagErrorText
}STATUScurrentDESCRIPTION"A collection of managed objects that describe tests and errors
supported by each physical entity."::={ ciscoEntityDiagMIBGroups 1}ceDiagGlobalConfigGroup OBJECT-GROUPOBJECTS{ ceDiagBootupLevel }STATUScurrentDESCRIPTION"A collection of managed objects that describe global
configuration of the online diagnostic feature."::={ ciscoEntityDiagMIBGroups 2}ceDiagEntityGroup OBJECT-GROUP
OBJECTS{
ceDiagEntityBootLevel,
ceDiagEntityCurrentTestMethod
}STATUScurrentDESCRIPTION"A collection of managed objects that describe the state of a
physical entity with respect ot the online diagnostic
feature."::={ ciscoEntityDiagMIBGroups 3}ceDiagEntityImageGroup OBJECT-GROUPOBJECTS{
ceDiagEntityImageAdminStatus,
ceDiagEntityImageOperStatus,
ceDiagEntityFieldDiagnosticUrl
}STATUScurrentDESCRIPTION"A collection of managed objects that describe the diagnostic
image which the physical entity is running."::={ ciscoEntityDiagMIBGroups 4}ceDiagOnDemandGroup OBJECT-GROUPOBJECTS{
ceDiagOnDemandErrorAllowed,
ceDiagOnDemandErrorAction,
ceDiagOnDemandIterations,
ceDiagOnDemandJobSuite,
ceDiagOnDemandJobTestList,
ceDiagOnDemandJobPortList,
ceDiagOnDemandJobRowStatus
}STATUScurrentDESCRIPTION"A collection of managed objects that describe the diagnostic
on demand diagnostic jobs on the system."::={ ciscoEntityDiagMIBGroups 5}ceDiagScheduledGroup OBJECT-GROUPOBJECTS{
ceDiagScheduledJobType,
ceDiagScheduledJobStart,
ceDiagScheduledJobDayOfWeek,
ceDiagScheduledJobTestList,
ceDiagScheduledJobPortList,
ceDiagScheduledJobRowStatus
}STATUScurrentDESCRIPTION"A collection of managed objects that describe the diagnostic
on demand diagnostic jobs on the system."::={ ciscoEntityDiagMIBGroups 6}ceDiagTestPerfGroup OBJECT-GROUPOBJECTS{
ceDiagTestPerfLastResult,
ceDiagTestPerfLastErrorID,
ceDiagTestPerfLastRun,
ceDiagTestPerfFirstFail,
ceDiagTestPerfLastSuccess,
ceDiagTestPeffLastFail,
ceDiagTestPerfTotalRuns,
ceDiagTestPerfTotalFails,
ceDiagTestPerfConsecutiveFails
}STATUScurrentDESCRIPTION"A collection of managed objects that describe the performance
of tests supported by each physical entity."::={ ciscoEntityDiagMIBGroups 7}ceDiagHealthMonitorGroup OBJECT-GROUPOBJECTS{
ceDiagHMSyslogEnabled,
ceDiagHMTestEnabled,
ceDiagHMTestIntervalMin,
ceDiagHMTestInterval,
ceDiagHMTestIntervalDefault,
ceDiagHMTestThresholdDefault,
ceDiagHMTestThreshold
}STATUScurrentDESCRIPTION"A collection of managed objects that describe tests and test
configuration with relating to the health monitor."::={ ciscoEntityDiagMIBGroups 8}ceDiagEventGroup OBJECT-GROUPOBJECTS{
ceDiagEventLogSize,
ceDiagEventCount,
ceDiagEventMaxQueries,
ceDiagEventQueryPhysicalIndex,
ceDiagEventQuerySeverity,
ceDiagEventQueryOwner,
ceDiagEventQueryResultingRows,
ceDiagEventQueryStatus,
ceDiagEventResultPhysicalIndex,
ceDiagEventResultPhysicalDescr,
ceDiagEventResultTime,
ceDiagEventResultSeverity,
ceDiagEventResultLogText
}STATUScurrentDESCRIPTION"A collection of managed objects that describe online
diagnostic event history."::={ ciscoEntityDiagMIBGroups 9}ceDiagScheduledJobSuiteGroup OBJECT-GROUPOBJECTS{ ceDiagScheduledJobSuite }STATUScurrent
DESCRIPTION"A collection of managed objects that describe the test suite information
for a diagnostic scheduled job."::={ ciscoEntityDiagMIBGroups 10}ceDiagNotifControlGroup OBJECT-GROUPOBJECTS{
ceDiagEnableBootUpFailedNotif,
ceDiagEnableHMThreshReachedNotif,
ceDiagEnableHMTestRecoverNotif,
ceDiagEnableSchedTestFailedNotif
}STATUScurrentDESCRIPTION"A collection of objects providing enabling/disabling
of the boot up failed, health monitoring, and
scheduled job notifications for online diagnostics."::={ ciscoEntityDiagMIBGroups 11}ceDiagNotifErrorMsgGroup OBJECT-GROUPOBJECTS{ ceDiagEventErrorMsg }STATUScurrent
DESCRIPTION"A collection of objects providing error message used by
various notifications."::={ ciscoEntityDiagMIBGroups 12}ceDiagNotificationGroup NOTIFICATION-GROUPNOTIFICATIONS{
ceDiagBootUpFailedNotif,
ceDiagHMThresholdReachedNotif,
ceDiagHMTestRecoverNotif,
ceDiagScheduledTestFailedNotif
}STATUScurrentDESCRIPTION"A collection of notifications providing for boot up failed, health
monitoring, and scheduled job within online diagnostics."::={ ciscoEntityDiagMIBGroups 13}END